Licensed & insured · 28 years in Los Angeles

House foundations, built to hold.

We've poured 50+ house foundations across Los Angeles: new homes, ADUs and additions. Footings, slabs and seismic hardware go in to the engineer's plans and pass inspection. We also pour the driveway, patio and walls that go with the house.

Office +1 888-885-5834 · Cell +1 213-267-7743
50+
House foundations poured in LA
4,000
PSI standard mix
#4
Rebar at 18" on center
28
Years in the LA market
What we build

Foundations first, then everything around the house

Builders, developers and homeowners call us for the foundation, and we stay for the flatwork. We work from your engineer's plans, coordinate LADBS inspections, and pour with ready-mix from local LA plants.

New home foundations

Slab-on-grade and raised foundations for new single-family homes, from layout to final pour.

Engineered plans · seismic hold-downs

ADU foundations

Backyard and garage-conversion ADUs, including tight lots with limited truck and pump access.

Slab-on-grade · utility sleeves set

Additions & footings

New footings tied into existing foundations for room additions and second-story work.

Dowelled into existing · epoxy anchors

Retaining walls

Poured walls for hillside lots, with drainage behind every wall.

Gravel backfill · weep holes

Driveways & flatwork

Driveways, patios and walkways to finish the job once the house is framed.

5" slab · saw-cut joints

Repair & resurfacing

Crack repair, slab leveling and overlays for older homes and slabs.

Epoxy injection · micro-topping
Crew & equipment

Our capacity

Our own crew and our own trucks, not subcontractors. Every icon below is one person or one truck on our team.

32Concrete workers
3Experienced supervisors
4Concrete mixer trucks
8Pickup trucks
Foundation types · California code

Foundations we build

Typical details for the foundations we pour across Los Angeles, dimensioned to the 2025 California Residential Code (CRC), California Building Code (CBC) and CALGreen. Each numbered tag matches a code note under the drawing.

8" MIN 12" MIN 12" MIN 3½" MIN SLAB 4" BASE 1 2 3 4 5 6

Slab-on-grade

The most common foundation for new homes and ADUs on flat lots: a reinforced slab with turned-down footings at the edges.

  1. 1Slab 3½" thick minimum.CRC R506.1
  2. 2Vapor retarder in contact with the slab, over a 4" base of ½" or larger clean aggregate.CALGreen 4.505.2.1 · CRC R506.2.3
  3. 3Footing 12" wide minimum, bottom 12" minimum below undisturbed ground. Wider for two stories per Table R403.1(1).CRC R403.1.1 · R403.1.4
  4. 4One #4 bar at the top and one at the bottom of the footing in Seismic Design Category D.CRC R403.1.3.2
  5. 5½" anchor bolts, 7" embedment, 6'-0" on center max and within 12" of each plate end, with 3"×3"×0.229" plate washers.CRC R403.1.6 · R602.11.1
  6. 6Treated sill plate at least 8" above finished grade; grade falls 6" within the first 10'.CRC R317.1 · R401.3
WOOD FLOOR FRAMING CRAWL SPACE 8" MIN 12" MIN 12" MIN 6" MIN 18" MIN 1 2 3 4 5 6

Raised foundation

Concrete stem walls on continuous footings, carrying a wood floor over a crawl space. Used for traditional homes and for additions that match an existing raised floor.

  1. 1Footing 12" wide × 6" thick minimum for one story, larger per Table R403.1(1); bottom 12" minimum below undisturbed ground.CRC R403.1.1 · R403.1.4
  2. 2Concrete stem wall with its top at least 8" above finished grade.CRC R404.1 · R317.1
  3. 3One #4 bar within 12" of the top of the wall and one #4 bar 3"–4" from the bottom of the footing (Seismic Design Category D).CRC R403.1.3.1
  4. 4½" anchor bolts, 7" embedment, 6'-0" on center max, with 3"×3"×0.229" plate washers.CRC R403.1.6 · R602.11.1
  5. 518" minimum from ground to the bottom of floor joists (12" to girders), or the framing must be treated wood.CRC R317.1
  6. 6Under-floor vents of 1 sq ft per 150 sq ft of crawl space, plus an 18"×24" access opening.CRC R408.2 · R408.4
5" TYP. EXPANSIVE CLAY SOIL 1 2 3 4 5 6

Post-tensioned slab

Steel tendons run through the slab and are tightened after the pour, so the slab stays in compression when clay soil swells and shrinks.

  1. 1Slab and beams designed for expansive soil per PTI DC10.5.CRC R403.1.8 · CBC 1808.6.2
  2. 2½" 7-wire, 270 ksi strand (ASTM A416), sheathed, set at slab mid-depth.PTI DC10.5
  3. 3At least 50 psi average precompression after losses.PTI DC10.5
  4. 4Perimeter and interior beam sizes set by the engineer from the soils report.CBC 1803 · 1808.6
  5. 5Tendons stressed once concrete reaches the specified strength; stressing pockets grouted.Per structural plans
  6. 6Vapor retarder in contact with the slab over a capillary break.CALGreen 4.505.2.1
EMBED DESCENDING SLOPE BEDROCK 1 2 3 4 5 6

Caisson & grade beam

Drilled concrete piers go down to bedrock and are tied together by grade beams. The standard for hillside homes in neighborhoods like the Hollywood Hills.

  1. 1Soils and geology report required; its recommendations set pier size and depth.CBC 1803
  2. 2Drilled cast-in-place concrete piers with vertical bars and ties, sized by the engineer.CBC 1810
  3. 3Piers embedded into bedrock or competent material to the depth in the soils report.CBC 1803 · 1810
  4. 4Grade beams tie the piers together in both directions (Seismic Design Category D).CBC 1810.3.13
  5. 5Foundation set back from a descending slope face H/3, up to 40 ft, unless the soils report allows otherwise.CBC 1808.7.2
  6. 6Special inspection during drilling, reinforcing and concrete placement.CBC 1705.8
BASEMENT 3½" MIN 12" MIN 1 2 3 4 5 6

Basement walls

Reinforced, waterproofed walls that hold back soil on every side, with a drain at the footing. For basements, subterranean garages and levels cut into a hillside.

  1. 1Reinforced concrete foundation wall per CRC tables, or engineered as a retaining wall.CRC R404.1 · CBC 1807
  2. 2Waterproofing from the top of the footing to finished grade where living space is below grade.CRC R406.2
  3. 3Perforated drain on 2" of gravel, covered by 6"; gravel runs 12" past the footing and 6" above it, wrapped in filter fabric.CRC R405.1
  4. 4Slab 3½" minimum over a vapor retarder.CRC R506.1 · R506.2.3
  5. 5No backfill until the floor above is anchored or the wall is braced.CRC R404.1.7
  6. 6Continuous footing with #4 bars, sized for wall load and soil bearing.CRC R403.1 · R403.1.3
3" CLR LOAD SPREAD OVER WHOLE FOOTPRINT 1 2 3 4 5 6

Mat foundation

One thick, double-reinforced slab under the whole building. It spreads the load across weak or uneven soil where separate footings would settle.

  1. 1Mat thickness and reinforcing designed by the engineer.CBC 1808 · ACI 318
  2. 2Top and bottom bars each way, at least 0.0018 × the gross concrete area.ACI 318 minimum slab steel
  3. 33" clear cover where concrete is cast against earth.ACI 318 cover requirements
  4. 4Column and wall dowels fully developed into the mat.ACI 318
  5. 5Allowable bearing and expected settlement taken from the soils report.CBC 1803
  6. 6Vapor retarder in contact with the slab over a capillary break.CALGreen 4.505.2.1

Typical details for illustration, not to scale. Every foundation is built to the stamped structural plans, the soils report and the approved permit for that project.

Pick your shade

Six finishes, fifty shades

Every finish can be tinted with integral color, from bright white cement to deep charcoal. Tap a finish to see where it works best.

Broom finish

Fine ridges pulled across the wet surface for grip. The standard for driveways, sidewalks and anything that gets wet. Least expensive and easiest to repair.

How a pour goes

From plans to a slab ready for framing

Every foundation follows the same sequence, so builders know when the framers can start.

Step 1

Plans & bid

We review the structural plans and soils report, walk the site, and send a written, line-item bid.

Step 2

Layout & dig

Layout staked, footings excavated to depth, and forms set to the engineer's dimensions.

Step 3

Steel & inspection

Rebar tied, hold-downs and anchor bolts placed, plumbing sleeves set. LADBS signs off before the pour.

Step 4

Pour & cure

Ready-mix placed and finished, then kept moist while it cures. Framers can typically start within days.

Service area

All over Los Angeles

We work throughout LA County. If your neighborhood isn't listed, call us. If we can get a truck there, we can pour there.

  • Silver Lake
  • Echo Park
  • Los Feliz
  • Highland Park
  • Eagle Rock
  • Pasadena
  • Glendale
  • Burbank
  • Studio City
  • Sherman Oaks
  • Van Nuys
  • Culver City
  • Mar Vista
  • Venice
  • Santa Monica
  • Westchester
  • Inglewood
  • Long Beach
  • Downtown LA
  • + LA County
Free estimate

Send us your plans

Tell us about the build and we'll review the plans and walk the site. Bids are free, written and itemized.

Office+1 888-885-5834
Cell / text+1 213-267-7743
Office address615 S Grand Ave
Los Angeles, CA 90017
CredentialsLicensed & insured · 28 years in the market
Fifty Shades of Concrete

615 S Grand Ave, Los Angeles, CA 90017 · +1 888-885-5834 · Licensed & insured

© 2026 Fifty Shades of Concrete